V-HOP 350, V-HOP 450, V-HOP 550,
V-HOP 650, V-HOP 750

Product Data		Click on icons below for an explanation of terms
	Clamping Force	20 -150 ton

	Swing Angle	60° - 90°

	Adjustable Stroke	Yes

	Adjustable Chuck Waiting Position	Yes

	Linear Guide	Yushin Linear Rail

	Controller	G-type

Runner take-out robots for vertical clamp moulding machines. These are very effective when taking out runners from vertical clamp moulding machines
Swing function. The angle of rotation can be adjusted between 60 and 90 degrees, allowing runners to be released at any location.
Applicable to product take-out from either the lower or upper mould. Products can be taken-out from either the lower or upper mould half simply by changing settings.
Multilingual display selection (optional). This comes standard with a G-type controller,which is available with an optional multilingual displays election function oriented the international market.

Standard Specification

Power Source	AC200V (50/60Hz)
Control Method	Sequence Stored Program
Working Pressure	0.4 - 0.5MPa
Maximum Allowable Pressure	0.8MPa

Model		V-HOP350	V-HOP450	V-HOP550	V-HOP650	V-HOP750
Stroke	Entry (mm)	350	450	550	650	750
	Descent (mm)	90
	Swing	Min.60 - Max.90
Transverse Standby Position Adjustment (mm)		Waiting position adjustable range 60mm
Air Consumption Litre (Normal)/Cycle	No Reversal	8	10	12	14	16
Air Consumption Litre (Normal)/Cycle	Reversal Possible	12	14	16	18	20
Maximum Weigh Capacity		1.5Kg
Robot Weight		37kg	38kg	39kg	42kg	43kg

Dimensions

Model	V-HOP No Rotation No Reversal	V-HOP-X No Rotation Reversal Possible	V-HOP-R Rotation Possible No Reversal	V-HOP-RX Rotation Possible Reversal Possible
A	-	-	90	90
B	-	-	30	30
C	350(450) [550]<650><<750>>
D	817(917)[1017] <1117><<1217>>	929(1029)[1129] <1229><<1329>>	817(917)[1017] <1117><<1217>>	929(1029)[1129] <1229><<1329>>
E	522	634	522	634
F	295(395) [495]<595><<695>>
G	-	180	-	180
H	952
I	212
J	361
K	104
L	90
M	271
N	110
O	30
P	160
Q	330		505
R	160
S	200
T	-	-	137
U	100		163
V	100		125
W	400

Values in ( ) are for the 450type.
Values in [ ] are for the 550type.
Values in < >are for the 650type.
Values in << >> are for the 750type.
*The B dimension in the illustration indicates the range within which the rotation angle can be adjusted

Option List

Option	Explanation
R option	The position at which runners are released can be set by adjusting the swing angle between 60 and 90 degrees.
X option	When runners are released after extraction from the upper mould, the chuck rotates 180 in the opposite direction to prevent runners from hanging so runners are released facing downward.
Conveyor signal linking	Operation can be linked to the belt feed of a pool conveyor, by connecting an optional metal outlet, enabling moulded products to be stocked in shot units.
Special color	The customer can specify a special color for the robot and the control box, etc.
External Part removal detection	After runners have been extracted, they can be detected by a limit switch.
Special base for attachment to a vertical clamp injection-moulding machines where there is no room on the horizontal surface of the moulding machine to mount the robot.	The robot base allows the robot to be mounted to the side of the moulding machine base.
Special base for attachment to a vertical clamp injection-moulding machines where there is no room on the horizontal surface of the moulding machine to mount the robot.	The base allows mounting the robot to the floor.
Safety door signal	This signal monitors when the safety door of the moulding machine is closed. Extraction cannot begin during automatic operation unless this signal is on.
Automatic injection signal	The robot can use the automatic injection signal output from the moulding machine as a condition to begin extracting. This initiates automatic operation only when parts have been moulded.